What is PV system shade loss?
- Nearby objects, such as trees, antennas or poles
- “Self-shading” from other PV panel rows
- Horizon shading from the terrain surrounding the installation site
- Other factors such as panel orientation, soiling or differential aging
Effects of shade on solar output
So what does that mean for solar power efficiency?
Intuition suggests that the power output of the panel will be reduced proportionally to the area that is shaded.
However, this is not the case. In his book Renewable Energy and Efficient Electric Power Systems Stanford University’s Gil Masters demonstrates how shading just one out of 36 cells in a small solar module can reduce power output by over 75%.
That’s right, shading just 1/36 of the cells can reduce power output by 75%.
Why can minimal shading cause severe power loss?
To conceptualize why shading results in such severe losses, it is helpful to use the analogy of water flowing in pipes. The flow rate of water through the pipe is constant, much like the current through a cell string is constant for a given irradiance level.
Shading a solar cell is similar to introducing a clog in a pipe of water. The clog in the pipe restricts the flow of water through the entire pipe. Similarly, when a solar cell is shaded, the current through the entire string is reduced.
This is significant because every cell in the cell string has to operate at the current set by the shaded cell. This prevents the unshaded cells from operating at maximum power.
Essentially, every cell is like a chain in a link. The shaded cell is the “weakest link”, reducing all the remaining cell’s power availability. So yes, only a small amount of shading can have a dramatic effect on the power output of a solar panel.
Similar principles apply to PV modules connected together. The current flowing through an entire string of modules can be heavily reduced if even just a single module is shaded, leading to a potentially significant loss of power output.
How to reduce shading losses: Solar panel shading solutions
You may have read the previous paragraphs and thought that hope was lost for your PV system to be efficient, but fear not! Fortunately, there are a number of different approaches that can be applied in PV system design to reduce shading losses. These include the use of different stringing arrangements, bypass diodes, and module-level power electronics (MLPEs).
Modules connected in series form strings, and strings can be connected in parallel to an inverter. The current through all the modules of a string has to be the same, and the voltage of parallel strings has to be the same.
As we saw in the last section, a shaded module in a string can bring down the power output of the string significantly. However, a shaded module in one string does not reduce the power output of a parallel string. Therefore, by grouping shaded modules into separate strings, the overall power output of the array can be maximized.
For example, in a commercial system with parapet walls, it can be beneficial to group modules that receive shade from the parapets into strings, and keep modules that do not receive shade from the parapets in separate, parallel strings. This way the unshaded strings can maintain a higher current and power output.
Bypass diodes are devices within a module that allow the current to “skip over” shaded regions of the module. By utilizing bypass diodes, the higher current of the unshaded cell strings can flow around the shaded cell string. However, this comes at the expense of losing the output of the cells that are skipped over.
Although it would be theoretically ideal to have a bypass diode for each solar cell, for cost reasons a typical solar module will have three bypass diodes, effectively grouping the cells into three series cell strings (see below). For instance, a 60-cell module will typically have one bypass diode for every 20 cells.
Module Level Power Electronics (MLPEs)
MLPEs are devices that are attached to individual modules in order to increase performance under shaded conditions (though there are other benefits, such as mismatch mitigation and module-level monitoring).
This is done by performing maximum power point tracking at the module level. MLPEs include DC optimizers and microinverters.
A DC optimizer adjusts its output voltage and current to maintain maximum power without compromising the performance of other modules.
For instance, when a shaded module produces electricity with a lower current, the DC optimizer will boost the current at its output to match the current flowing through the unshaded modules; to compensate, the optimizer reduces its output voltage by the same amount it boosts the current. This allows the shaded module to produce the same amount of electrical power without impeding the output of other modules. A system utilizing DC optimizers still needs an inverter to convert electricity from DC to AC.
As opposed to having a single inverter servicing all of the panels, each panel can have a small inverter attached to it to convert its output from direct current (DC) to alternating current (AC). Since each microinverter has an MPPT, and their outputs are connected in parallel, each panel will operate at its maximum power point, without impacting other panels.
Shade loss techniques compared — using Aurora Solar
Using Aurora’s simulation engine, we compared the performance of three different PV systems subject to significant shading.
As shown in the figure below, we placed a 3.12 kW system near the edge of a roof, which has tall trees next to it. Note that while this design effectively showcases the performance difference of these system topologies in shaded conditions, it is not an optimal—or even a practical — design. Our findings are summarized in the table in the “Results” section below.
Results from performance simulations of PV system on a Palo Alto home utilizing different MLPE components. The difference between the two MLPE outputs is attributed to the differences in their inverters’ efficiencies. Source: Aurora Solar.
|System Topology||Annual Yield||Improvement with MLPEs|
|String Inverter||2,585 kWh/year||N/A|
|DC Optimizers||3,035 kWh/year||+17.3%|
Our results show that using MLPEs under these conditions increases system output by 17.3% annually, showing the benefit of using these components for shade mitigation. Additionally, the effective yield of a system using a microinverter or a DC optimizer is approximately the same, although there could be small differences (on the order of 1%) in some cases due to differences in efficiency curves.
For the same reason that they can mitigate shade losses by decoupling module output, MLPEs can eliminate module-to-module mismatch losses. These losses are typically caused by manufacturing variations that lead to slight differences in the electrical characteristics of two modules of the same type. Since MLPEs allow the modules to operate independently from one another, these variations will not impact the system’s overall performance.
Solar PV education 101: a series
This article on Shade Losses for PV Systems, and Techniques to Mitigate Them is part of Solar PV Education 101, a six-article series that serves as an introductory primer on the fundamentals of solar PV for beginners.
Learn more about the fundamentals of solar by subscribing to our blog.
See the Other Articles Here:
Article 1: The Beginner’s Guide to Solar Energy
Article 5: Shade Losses for PV Systems, and Techniques to Mitigate Them
What happens when a solar panel is shaded?
When a solar panel is shaded, the energy output of the solar panel is notably less than it would be if the solar panel was not shaded.
How much does shade reduce solar panel output?
Solar panel output can be significantly reduced because of too much shade on a solar module.
As previously mentioned, Gil Masters shares in his book, “Renewable Energy and Efficient Electric Power System,” that shading one out of 36 cells in a small solar component can reduce power output by over 75%.
Do solar panels work if partially shaded?
Even though solar panels produce less energy when partially shaded, the panels still do operate properly and generate some electricity.